Families with kids have always been concerned about the prospect of lead in water. We are now aware of the damage that lead causes to the body.
In addition, a lot of people are puzzled how it gets into their drinking water and what the solution is.
How lead makes its way into the water.
Lead is a bluish-gray metal that occurs naturally in small quantities on the outer layer of the earth. It’s not normally found in water when it leaves the treatment plant. Thorough tests are constantly carried out to avoid that.
Lead is not commonly found naturally in water. If you suspect that there is lead in your water or private well, you may collect drinking water samples in a laboratory.
Lead usually passes through the pipes that link the plant to your home. Another source comes from the solder used to connect the plumbing and fittings.
Although lead is no longer used, it was not until the mid-1980s that it was not allowed to be used to connect to the public water system. It is likely, if your pipes were installed earlier, that they are made from lead.
Should you worry about lead in water?
Lead poisoning has several adverse effects on the human body, especially in children less than six years old.
1) In younger children, lead poisoning can delay growth and has been associated with behavioral issues as they age.
2) Prolonged exposure can result in damage to red blood cells, kidneys, nervous system and brain.
3) Although some lead ends up in human waste, much of it is stored in bones. Eventually, it can be a poison to your body. At very high levels, it may cause convulsions in children, or death.
4) Minuscule levels may also cause learning disabilities, hearing impairments, developmental delays and many other irreversible problems.
With the many worries and the manner in which it affects the body. What remedies are available?
How to remove lead from drinking water
Heating or boiling your water is not going to remove the lead. As some of the water evaporates during the boiling process, the lead content of the water may actually rise slightly as the water is boiled.
You may be able to decrease or prevent exposure to lead.
When the water has been sitting in the pipes, it is when the buildup occurs the most, so before using tap water, run it for at least a few minutes before using. It may take a few seconds to a few minutes, depending on recent water usage.
An alternative method of reducing lead exposure is to use only cold tap water for consumption and cooking. Hot water will break down lead solids, and this is the most probable source for the highest levels of lead.
These are the simplest ways to get rid of lead in old houses, which have plumbing and fittings.
There are other ways to get rid of lead in your water as well.
One of the most common ways to get rid of lead in your drinking water is through some form of water filtration. The best system is a whole house filter, as it is connected to the main inlet water pipe.
Both types are the most economical way to filter lead, but it is important to know that not all filters are the same. You have to read the data sheet carefully, to make sure that it filters out at least 99% of the lead, and other harmful contaminants in your drinking water.
One system that is highly recommended is activated carbon filtration. Besides eliminating lead, it also eliminates chlorine and all its associated by-products and many other pollutants.
Best Water Filter Pitchers For Lead
Prior to listing the best water filter pitchers for lead, it is essential to pay attention to the facts about lead filtration to make sure that you get clean, safe and lead-free water for consumption and everyday use.
These facts are regarding the best buying water filter jug, so you know what you should go for.
It ought to be:
- Tested and certified under NSF 53, for lead or tested by a laboratory certified by the State.
- Tested in tougher conditions to determine the impact of their claims. That is to say, lead reduction efficiency, the system was tested at a level 10% above (155-160) the 150 parts per billion certification requirement based on a 500 gallon test cycle.
- Tested under actual conditions through the addition of complex chemicals to chlorinated tap water.
- Utilizes selective filtration- filters contaminants and leaves a natural trace of minerals.
- More economical
- Easy to assemble and user-friendly.
- Supported by outstanding technical support.
- Got a lifelong guarantee.
Our water filtration team knows that. That’s why we introduce you to the latest innovative products from leading companies that will eliminate lead from your water
- ZERO eliminates 99% to 100% of heavy metals. No one comes close to consistency across the board.
- Best for lead reduction
- WQA certified to reduce lead and other harmful contaminants LED indicator
No time to read? Here’s a summary of our top water filter pitchers for lead
Let’s dive in…
1. Aquagear Water Pitcher
The Aquagear water pitcher is best known for removing fluoride, lead and 20x plus other undesirable contaminants. It has been rigorously tested under actual conditions in Flint, Michigan for lead and copper reduction and is certified to NSF Standards 42 and 53.
It is equipped with a dual filtration system that eliminates harmful metals from the water and improves the non-natural smell and tastes. Firstly, Aquagear uses absorbent carbon derived from coconut shells that eliminates organic compounds and pollutants from the water. As contaminated water passes through the Aquagear water filter, the absorbent carbon media trap and neutralize waterborne pollutants. This includes disinfectants such as chlorine, solvents, PCBs, PBDEs and compounds that cause bad taste and odor.
Additionally, Aquagear uses CRM ion exchange materials in a chelant matrix to effectively remove heavy metals, industrial and agricultural pollutants, and trace pharmaceuticals. Through adsorption, absorption, chemical bonding, chelation and deep filtration, Aquagear’s unique formulation of carbon exchange materials and activated ions turns regular tap water into high-quality filtered water. Because of its ion exchange process, Aquagear filter can increase TDS. The increase is simply the outcome of a well-functioning ion exchange process.
Fluoride (90.6%), chlorine (99.9%), chloramine (99.9%), chromium 6 (99.4%), lead (99.5%), mercury (97.8%), arsenic (99.8%), THMs (99%) and copper (99.7%) are eliminated.
In addition to contaminant removal, it has health benefits. Leaves a trace of calcium and magnesium. It will retain at least the alkalinity, but it is not designed to alkalinise the water.
The housing of the Aquagear water pitcher is made using antimicrobial materials and it’s BPA free. You will especially appreciate the size of the container. It is designed to fit any refrigerator.
It has a hole on the top of the lid for you to fill the container without having to remove the top. The lid tilts backwards, it is comfortable to raise and pull, and the handle has a good grip. This is essential to give a decent pour. You can pour from above without the need to lift the lid.
The filter will filter approximately 150 gallons of water or around 3-6 months. For a larger family, obviously you’d be replaced sooner. The difference between tap drinking water and Aquagear filtered water is instantly noticeable. This pitcher provides unparalleled filtration and tasty water.
|Tested and certified by both BPA and (FDA) and it is very light in weight.|
|Screens for contaminants and leaves natural traces of minerals.|
|It is quick and easy to install & comes complete with simple guide.|
|Does not remove microplastics|
|Does not remove giardia or Cryptosporidium|
|Does not purify water for aquarium use|
2. Clearly filtered water pitcher
Clearly filter is made of a premium kind of plastic called Tritan. It is BPA free, BPS free, EA free, and phthalate free. This filter is mostly known for its updated designs and its significant reduction in contaminants. It removes more than 230 contaminants (including fluoride by up to 98%) from tap water with a 99.7% average improving water quality. Contaminant reduction is based on combining the latest and most efficient purification mechanisms.
The pitcher filter consists of approximately 4 filtration steps. It features Affinity® filtration technology, which includes approximately seven different materials selected for their filtering properties. The process does not remove the beneficial trace minerals (calcium, magnesium, potassium).
It involves ion exchanges stage, which consists of trapping molecular-size ions of lead and other metals, exchanging them for healthy and tasty sodium and potassium ions. Measuring TDS might not be accurate, because the filter will pick up on healthy minerals in parts per million. It cannot detect contaminants that are harmful in much smaller quantities. For example, lead and mercury are dangerous in parts per billion, sometimes parts per trillion.
The filters are also tested and certified to meet NSF/ANSI requirements. It delivers on a variety of safety concerns.
The filter reduces the taste of chlorine and odors, removes sediments, lead, cysts and a whole series of other unpleasant things. The screening process is slow, and this can be annoying and frustrating. But the time spent passing the filter will show if the pitcher filters well because good filtration requires good contact time.
If you filter the colored water, it will remove virtually all the color from the water due to the unique ion exchange resin mixture in conjunction with carbon. Another interesting feature of this pitcher is that you can pour water while you filter, unlike other pitchers, which do allow water from the lower reservoir out of the spout.
A well-designed water filter pitcher should provide good water, and it should be straightforward. Complicated assemblies or filter changes can ruin the deal. To use this pitcher correctly run your fingers, using slight downward pressure along the 3 edges of the rear lid. The removable rear lid has a short lip that goes under the back of the spout’s lid. And the removable rear lid has small ridges that fit snugly into the grooves on the edge of the pitcher. It’ll virtually ‘snaps’ into place.
Clearly, the water filter is another pitcher which offers an incredibly practical way to filter the water to drink. It is one of the finest water filter pitchers built for durability and robust design underlining a wooden handle. The average lifespan of the pitcher is about 6 months or 100 gallons.
After six months or after 100 gallons, its effectiveness starts to decline. You might want to replace the water quality drops right away. You will instantly notice an enormous improvement in taste. On top of that, these filters last for a long time.
|Easy to clean|
|Easy to set up|
|Value for money|
|Has a long service life|
|It preserves essential minerals|
|Does not have a filter gauge that shows when to change the filter|
|Does not filter radiation.|
3. Pur Water Filter- Lead Reduction Water Filter Pitcher
The PUR water filter is best known for reducing lead and its certified to filter up to 40 gallons or 2 months. This water filter pitcher is made of Polystyrene and it’s BPA free. It filters water in two stages, producing which is clean healthy water.
The PUR filter is also known for bacterial reduction because it rates high for cyst reduction. It’s also certified to remove Cryptosporidium and giardia. These are parasites found in drinking water. Others are not certified to remove them
Other contaminants include Mercury, Cadmium, Copper, Zinc, Chlorine, Taste and Odor, Particulate Class I, Microbial Cysts, Benzene, Carbon Tetrachloride, Tetrachloroethylene, TCEP, 2,4-D, Atrazine, Simazine, Linuron, Atenolol, Carbamazepine, Estrone, Trimethoprim, Bisphenol A (BPA) and Nonyl Phenol.
This model is a large capacity pitcher, and it filters relatively rapidly. The filling of the upper chamber will filter approximately 1/2 pitcher, so you will need 2 filtration cycles per pitcher. Each cycle lasts up to 20 minutes, which means that a complete pitcher can take up to 40 minutes.
It pours carefully and simple to assemble. While using, first of all, allow the water to flow through the filter. Do not attempt to pour until all the water has drained through the filter. Also, do not fill to bottom of filter reservoir. Less is better here. Then pour into your cup. Just pour in slow. You cannot pour fast with this pitcher. Once you get the hang of it, it runs very smoothly.
The pitcher is available with fruit flavored cartridges. The cartridges come in raspberry, peach, strawberry, lemon and grape flavors. Flavors are a smart feature. You will pass from taking flavored sparkling waters and soft drinks to drinking more water with these flavor cartridges.
Pur water filters have a built-in LED indicator on the purifier, which tracks the life of the cartridge and warns you when to change the filter. The green light on the LED indicates that the filter is working properly. Yellow indicates that it is time to consider replacing the cartridge, whereas red means that you need to replace the pitcher immediately because the cartridge does not filter. This usually occurs every four months, but it depends on the use of the filter.
|Easy to assemble, it is accompanied by an easy guide.|
|LED indicator alerts you when you should get a replacement.|
|Low cost & efficient.|
|Fits perfectly in the refrigerator. The pitcher is 10-½” tall, 12” deep, and 5” wide.|
|This unit comes apart easily for cleaning|
|Does not filter fluoride and arsenic|
|Not rated for PFOA or PFOS|
4. ZeroWater ZP-010, 10 Cup Water Filter Pitcher with Water Quality Meter
Effectiveness and elegance come to mind when you deal with Zero Water Filter Pitcher. All ZeroWater® water filter pitchers include a 5-stage filtration system that eliminates 99% to 100% of heavy metals. There are no mineral or solids left of any kind using the zero filter. That’s how it gets a 000 reading on a TDS meter. No one comes close to consistency across the board.
With an 80 oz capacity, this larger-sized water pitcher can hold up to 10 cups of water and is tested by an independent laboratory. ZeroWater filters are NSF certified for the removal of chromium and lead. This is the only mark qualified to remove 99% of TDS, equivalent to the quantity of purified bottled water.
It has a sleek BPA-free and drip-free spigot making it ideal for office as well as home use. With its Ready-Pour® technology can pour a glass of filtered, clean water, while the filter continues the filtration process. No need to wait until the pitcher is full to start enjoying the purest tasting water.
While other filters use a carbon filtration method, it uses ion exchange technology. The ion exchange technology is very efficient, apart from the fact that it uses five filtration steps. The highest standard is guaranteed.
Zero water filters come with a water quality meter included. You can test your water to find out the quality of your water. The battery in the meter is good for 1000 hours of work.
The dirtier your water, the sooner the filters needs replacing. If your water is so bad you have to replace the filters more often than you like. If you take your water out of a swamp, it is likely that your filter might last for a day. Any one with numbers above 70 PPM needs to use a prefilter to reduce the amount of work the Zero water has to do to get your number to zero.
So there are no minerals, which is why the water is acidic. Nevertheless, the advantage afforded by this system makes it a worthwhile investment.
|Pure tasting water|
|Water quality meter included for free tests|
|Quick Fill spigot|
|Does not remove microbiological contaminants|
|NOT certified for the reduction of fluoride|
|slightly acidic water|
5. Seychelle pH2O Alkaline Water Filter Pitcher
This practical water filter pitcher removes any detectable contaminants from tap water. The longest-lasting water filter pitcher with a capacity of 200 gallons, the Seychelles water filter is a high quality filtration that’s defined by its next level life of 200 gallons and a quick flow of 1.3 liters per minute. The pitcher is made of top quality ABS plastic and is also BPA-free and FDA approved so that it can withstand wear for the future.
The filtering is a top-down/vertical process, playing out between the top–or fill–reservoir feeding the twin filters. The filters are a high-tech, porous, BPA-free micro-filter, infused with both granulated activated coconut carbon and Seychelles proprietary adsorbent media.
Seychelles has created a uniform 2 micron absolute pore size for the assured reduction and removal of the five contamination zones. Depending on the quality of the filtered water source, Seychellois pH alkaline filters may increase pH levels to 9.5. TDS ppm will increase 100-200ppm due to the the infusion of minerals into the filtered water.
Each filter has a 100 gallon capacity, giving this 64oz pitcher a 200 gallon capacity overall. Under normal use, this will provide approximately 6 months of highly filtered alkaline water. This time frame can vary depending on the water quality that is being filtered.
Contaminant removal by adsorption results in molecular attraction of substances to the carbon surface. The 2 micron controlled filter contains thousands of interconnected omnidirectional pores which result in a “tortuous path” for a higher reduction of analytes.
By forcing the water source through the filter, contaminants and pollutants are eliminated, while beneficial trace elements are retained. Seychelles’ proprietary ionic adsorption microfiltration coordinates all contaminant reduction processes through adsorption, absorption, chemical bonding, chelation and deep filtration.
Each product is designed to ensure maximum contamination reduction. The overall effect is an improvement in the quality of your water by increasing its taste and removing unpleasant color and odor.
The micro-porous body of the filter removes
- Aesthetic – unpleasant taste and odors, cloudiness, silt, sediment, chlorine, and chlorine byproducts.
- Chemicals – toxic chemicals (VOCs), trihalomethane, PCB, PCE, detergents and pesticides.
- Dissolved Solids – heavy metals including aluminum, fluoride, cadmium, chromium 6, copper, lead, arsenic, and mercury
This pitcher filter also has a compact design to fit in tight spaces. It fits nicely, even in the door of your fridge. Irrespective of its compact size, it has great volume that can be filled with up to 7 ½ cups. This saves time and energy since you do not have to fill the pitcher of the water filter frequently.
|Delivers clean and healthy drinking water.|
|Compact for fitting into tight spaces.|
|Removes 90% of fluoride|
|A large holding capacity|
|Pours well and lid stays on|
|All materials are 100% BPA Free.|
|It doesn’t come with a tester|
|Do not remove viruses or bacteria.|
|Does not filter out radiation|
|None recyclable material|
6. Culligan PIT-1 Water Filter Pitcher
Stay hydrated with Culligan pitcher filter, another water filter pitcher for lead that effectively removes bad taste & odor, aesthetic chlorine taste & odor, mercury, copper, Particulate Class VI, and zinc to WQA standards.
Culligan hits all the right spots when it comes to delivering the highest quality drinking water. It is the ideal size for a mini fridge, and holds enough water. Two things stands out about this item: the quality of the design, and the level of taste improvement of the drinking water.
The pitcher is a small, sturdy product that has this huge handle. I suppose from reading the comments of other pitcher of water, Culligan made sure to design a handle that could “handle” the stress of a full jug without cracking. This pitcher is meant for the long haul.
The improved taste of the water is fantastic. It filters the water so well. The big problem though is the amount of time it takes to fill the pitcher through the filter that might be a downside. Filling the filter chamber takes approximately 3-4 minutes to get through completely. In addition, the pitcher takes at least two filter chambers refills.
You can’t beat the price. It’s an extremely cheap pitcher. The lid is thin and flimsy. It doesn’t snap or lock but it works. The materials used to make these filters are also BPA-free and there is no need to soak them to improve their efficiency. Ensure always its stored in the refrigerator. This water filter pitcher will give you a nice clean, crisp taste of water.
|It can be refilled with generic filters, which are very easy to find.|
|Light weight & space saving|
|Works very slow|
|slightly acidic water|
7. Brita Longlast Everyday Water Filter Pitcher
Refresh yourself with another perfect water filter pitcher of our time, the Brita water filter pitcher. This pitcher can not only be used at home, you can pack it and bring it to the campsite with you. It is suitable for office space as well. It is certainly a durable product able to withstand tough conditions due to its elegant and durable design.
Made of BPA-free plastic and they are simple to replace with a pull top cap for easy removal. Its cartridges are compatible with all Brita pitchers and dispensers except Stream. Similarly, it is also independently lab tested to guarantee you of its unmatched prowess.
Brita Longlast Filter water filter pitcher uses a coconut-based activated carbon filter that removes contaminants. The mechanical process is that the cartridge fits into the tube underneath top (white) part of the pitcher and seals the upper tank so that water only descends into the bottom as it is filtered. To get almost a full bottom tank takes about 2 and a third fillings of the top.
Its NSF/ANSI Standards 42 and 53 to reduce lead by 99% and is certified to reduce chlorine (flavor and odor), asbestos, mercury, benzene, particulate class 1,cadmium and more. It’s however not certified to remove iron from well water. It’s not also certified to remove coliform bacteria.
|Nice solid BPA-free plastic|
|Effective for up to 6 months or 120 gallons|
|NSF/ANSI Standards 42 and 53|
|Slow but worth it. The Water is so good|
|Flimsy lid and getting it to securely fit into the pitcher is a hassle|
|This filter does not have an indicator|
|It does not filter out fluoride|
8. Waterdrop Lucid 10-Cup NSF Certified Water Filter Pitcher
The Water Drop pitcher features an innovative 7-stage water filter technology, which is NSF 42 certified to mainly d reduce arsenic, fluoride, lead, and other contaminants in water. Enjoy fresh, clean and healthy water straight from your tap with no additional bottled water costs. The taste of the water is truly a game changer.
The rate of fluoride removal depends on the specific quality of the water, the fluoride component in the water must be taken into account. Fluoride in water typically consists of inorganic fluoride and organic fluoride. For both types of fluorides above, it uses high-performance resin to remove inorganic fluoride and has used activated carbon to remove organic fluoride.
According to the lab test of the sodium fluoride, the removal rate of this is over 90%.
When you purchase this pitcher, it will come with one filter cartridge. The cartridge is mainly designed to reduce arsenic, fluoride, lead, and other contaminants in water promise you a healthier and more organic lifestyle.
The filter has been tested by WQA and is compliant with NSF 372. The pitcher filter uses silver-loaded activated carbon, which can prevent the growth of bacteria, but it cannot remove bacteria. It eliminates contaminants while maintaining minerals that are vital to your body, such as calcium, potassium, sodium and magnesium.
The water pitcher also pours the water favorably without losing its top, leaving the tap water filter in it. The lid can be removed by sliding it by hand to replace the filters or clean the pitcher. It holds up pretty well. You should, however clean the pitcher with soap and water and NOT in the dishwasher.
There are 2 ways to confirm a filter replacement.
1. The filtration capability of this pitcher can reach 200 gallons/3 months. Because of the differing water quality and water consumption of each home, the actual replacement time of the filter element is not uniform.
2. The indicator on the pitcher may help you find out when the filter should be replaced. The following three indicator states reflect the filter service life for your reference:
a. Blue light means “Good condition” with a max of 90 days of filter life.
b. Red Flash stands for “Replace Soon” with a 10-day grace period to replace the applicant.
c. The red light (stay on for 5 seconds) stands for “Replace Now”. At this point, you need to replace the filter right away to ensure the best water quality.
|Used in commercial and residential places|
|Does not reduce TDS|
|The company does not recycle waste cartridges.|
|Cannot remove chromium 6|
- 5 Best Chlorine and Chloramine Shower Filters: (Comparison Guide)
- 10 Best Shower Filters for Hard Water from Reddit:( No More Skin And Hair Damage)
- 5 Best Reverse Osmosis Systems to Remove Arsenic: (Reviews & Buyers Guide)
- 7 Best Faucet Water Filters from Reddit: (The Best Digs)
- 10 Best Countertop Water Filters Review from Reddit: ( Best Digs & Buyers Guide)
- How Do I Choose A Water Softener For My Well? (Ultimate Guide to Finding the Best Water Softener) - November 29, 2021
- Nuvoh2o Home Softener System - November 20, 2021
- Electric Baseboard Heaters Buying Guide:( Best Tips) - August 23, 2021